Air-VAC Engineering DRS24C Rework Station

Air-VAC Engineering DRS24C ID: 4038

Air-VAC Engineering DRS24C {ID: 4038}

Very complete system, ask about available tooling.
CEE ID: 4038
Status: Sold
Model: DRS24C
Vendor: Air-VAC Engineering
DOM: 2000
Condition: Inline with its age
Facilities: 220 VAC 60 Hz, 1ph 30A
Dims: 70" x 44" x 26" with table



Includes:
> tooling package (inquire)  
> double diffuser
> multi-media package
> IR sensor
> Site Solder Removal System
The DRS24 is designed to provide automated rework and low volume assembly of virtually any surface mount component including BGA's, QFP's, CSP's, connectors, sockets, PLCC's, and specialty components on a wide range of assemblies.
 
The system provides a high degree of automation including automated device pickup and removal, motorized beam-splitter vision, automatic placement using a precision force measurement system with realtime display and software-based process control of virtually all rework parameters, allowing the operator to follow a clear, simple procedure.
 
If complex functions are performed, they will be largely transparent to the operator.   For the process engineer, the controls and features of the system provide the flexibility and capability required to meet today's packaging and assembly challenges. Profiles and procedures can be easily modified to meet specific requirements. A concise, logical teach function allows profiles to be quickly and easily created or modified.
Component Requirements  
 
> Beamsplitter Vision System:  No minimum size, 2.0" square, 1.0" height  
> Direct View (perimeter):   No minimum size, 4.0" square, 2.0" height  
> Top & Bottom Side Clearance:  Top=1.12", Bottom=.920"   
 
Component Positioning Adjustments  
> Maximum Vertical travel:   5.0" (top to bottom travel)  
> Theta Adjustment:   ±10° (20° total)  
> X & Y Table: Manual control. Cable driven, backlash free design.
> Fine adjustment with resolution of less than 50µ  
 
Accuracy and Repeatability  
> Placement Accuracy: ±0.001" at 3σ (or a true position of 1.4 mil).  
> Repeatability: ± 0.0003"  
 
Force Measurement System  
> Component Placement Force: Up to 2000 grams in increments of 1 gram. Target point and ± range adjustment throughout process.  
 
> Auto Adjustment Capability: In-process adjustment of force value (± range)   
 
Thermal Profiling  
> Thermocouple Channels: 8 high speed K type thermocouple channels for profiling and process analysis.  Self calibrating. Resolution of 0.15 degrees C/res. bit.   
> Thermal SMART TRACK Software Management: Automatic thermal profiling software with profile optimization build function.  
IR Temperature Probe: Optional feature for monitoring to articulating arm. ± 3 degrees C.  
 
Heating Systems  
Top Heater: Patented 1000 watt, triple-pass (preheats incoming air) heating element with imbedded thermocouple for process (temperature) control.  
> Bottom Heaters: 4000 watt double diffuser convection preheater. Two independent temperature zones with automatic flow adjustment. 12" x 20" actual combined size.  
> Heater Controllers: All heaters controlled via a closed-loop, auto tuning PID controller. Self calibrating to ± 5° C.   
 
Microscope Optics  
> Stereo Microscope: Leica M3 binocular with adjustable 10X eyepieces, MZ6 1:6 zoom magnifier (seamless adjustment), custom focusing ring.   
> LTP Beamsplitter Vision: Patented alignment system for simultaneously viewing the component leads, while super-imposing the PCB pads (on top of each other).
> LED sensor for height reference and polarizing filter for (pad) contrast adjustment  
 
Illumination  
Green/White LED’s: Software controlled, independently adjustable vision lighting intensity provides enhanced optical contrast during alignment.
This unit is located in the CEE facility in the Chicago area. A CEE technician will demonstrate the unit fully functional for your live or video acceptance. If you require special acceptance criteria, please discuss this with your CEE sales agent. Availability is subject to prior sale.



Disclaimer

Information is provided for your convenience as our good faith estimate for this equipment. CEE does not warrant the accuracy of this information due to the nature of used equipment. Used equipment can be customized, altered, or simply worn beyond the capability to perform to original specifications. If certain details are critical for your application, we highly recommend testing the machines performance on that criteria. Please notify your CEE sales representative prior to purchase and we will propose solutions for your concerns. CEE's goal is always to minimize your risk.